PN00110-24C - Brushless (BLDC) 24v Motor Driver Speed Controller 15A - Makermotor

Makermotor provides variable speed gear motors and single speed motors for applications such as bbq rotissier motor, experimental motor for lab, conveyor motor system, and welding turn table. Our products cover speed range from low speed gear motors to high rpm variable speed motors.
Specifications: Shut-down at 6000 RPM Soft-start mode E-stop control 0-5vdc analog control PWM digital control (minimum 7kHz up to 16kHz) Reversible control Rated at 22-30 vdc Continuous duty at 15 amps DC Power supply friendly Fully enclosed Wiring Instructions:   Connect 3 phase wires (A, B, and C) to the 3 phase wires of your BLDC motor.  If you have a sensored BLDC motor, leave the hall sensor wires.  This controller does not require hall sensors. Connect thick red wire +24VDC (IN) to the positive terminal of your power supply or battery. Connect thick black wire 0V (GND) to the negative terminal of your power supply or battery. Make sure you connect your controller in the correct polarity.  Reverse polarity will damage this controller. To connect to a pot (potentiometer) for a manual control: Connect thin black wire 0V (GND) to your pot's GND. Connect thin yellow wire SIGNAL (IN) to your pot's Output. Connect thin red wire 5VDC to your pot's +Vcc. Introduce an on/off toggle switch between thin black wire and thin white wire REVERSE.  This will let you switch between CW and CCW rotations. Introduce an on/off toggle switch between thin black wire and thin blue wire STOP.  This will let you switch between stop and run functions. Introduce an on/off toggle switch between thin black wire and thin green wire SOFT START.  This will let you enable/disable the soft-start feature.  Soft start's ramp-up time is about 3 seconds. To connect to a microcontroller: Logic voltage has to be 5vdc. PWM needs to output at least at frequency of 7 kHz.  Maximum frequency is 16 kHz.  Connect your PWM signal to the thin yellow wire SIGNAL (IN). Switch signals between low (0vdc) and high (5vdc) to the thin white wire REVERSE for CW and CCW rotations. Switch signals between low (0vdc) and high (5vdc) to the thin blue wire STOP for stop (low) and run (high) functions.   Switch signals between low (0vdc) and high (5vdc) to the thin green wire SOFT START for enabling (low) and disabling (high) its feature.  Soft start's ramp-up time is about 3 seconds. To run as a single speed motor: Connect thin red wire to thin yellow wire. Connect thin green wire to thin black wire to enable the soft-start feature (recommended). Introduce an on/off toggle switch between thin black wire and thin white wire REVERSE.  This will let you switch between CW and CCW rotations.

Source The Right Wholesale brushless motor speed controller

YOUQUKEJI 2430 7200KV 4P Sensorless Brushless Motor with 25A Brushless ESC Electric Speed Controller for 1/18 1/16 RC Car Truck : Toys & Games

15A 24 Volt Sensorless BLDC Driver Board Speed Control

Electromen :: EM-151B BRUSHLESS DC MOTOR DRIVER 12-24V 25A

Yunir Brushless Motor Controller, Waterproof 24V-48V Motor Controller, LCD Display Electric Bike Scooter Brushless Controller Kit(36V/48V 350W) : Sports & Outdoors

Yunir Brushless Motor Controller, Waterproof 24V-48V Motor Controller, LCD Display Electric Bike Scooter Brushless Controller Kit(36V/48V 350W) : Sports & Outdoors

12V,24V,36V,5A,10A,15A 700W brushless DC motor driver,Hall sensor,brushless DC motor speed controller

Source The Right Wholesale brushless motor speed controller

24 Volt Electric Scooter Speed Controllers

Easy Operation: This DC Brushless Motor Controller is easy to operate, and the speed of the motor can be regulated by the potentiometer, you can

ICQUANZX DC 5V-36V 15A 3-Phase Brushless Motor Speed Controller Motor Control Board CW CCW Reversible Switch Motor Driver Control Regulator Module